1 · Identify the board
Let the reader match the physical board and choose the right column before looking up a rating.
Explore the board references and the first printable datasheet for Prime and Core.
Download draft PDFBoard names open the matching captures. Each row recommends specific information to carry into Smoothieboard V2 documentation. Source sections are grouped by function so manuals and shorter datasheets can be compared.
No boards match. Change the search or choose another category.
| Board | Sections and information | Apply to Smoothieboard V2 |
|---|---|---|
| Mesa 7I96SEthernet step/direction and machine I/O | Pinouts, jumper modes, isolated I/O ratings, encoder thresholds, firmware/reference registers, mechanical drawing | Use one table per terminal and separate ratings by output type. Keep register details in the firmware reference. |
| Mesa 7I76EEthernet motion and isolated field I/O | Field and logic power, expansion jumpers, connector pinouts, step/dir timing, field I/O, encoder modes, firmware and fault indicators, min/max tables | Show current with an explicit load condition and specify the exact rail. Expand serial register tables only in the integration reference. |
| Mesa 7I92TEthernet FPGA motion interface | Power and jumper options, connector variants, FPGA pin mapping, flash recovery, operating conditions, dimensional drawing | Show connector and power-source variants and label what changes with configuration. |
| Centroid AcornMill, lathe and router controller | Kit and bench setup, controller power, grounding, digital inputs, relay outputs, external drives, spindle and troubleshooting | Specify what the input expects electrically, including ground/common. Mark which hardware lives on the board versus an accessory. |
| Centroid AcornSixSix-axis step/direction controller | Logic supplies and bench test, inputs, output modules, drive wiring, spindle, encoder, PLC I/O, mounting | Document output state at startup and faults, and show mounting datum and connector clearances. |
| Centroid HickoryIndustrial EtherCAT motion controller | Drive compatibility, bench setup, grounding, isolated digital I/O, analog input/output specs, encoder setup, fault diagnosis | Identify input topology and signal reference. Keep drive compatibility and firmware setup in an integration appendix. |
| Centroid OakExternal servo-drive motion controller | Board overview, power, analog drive interface, encoder inputs, selectable input voltage, PLC expansion and connector pinouts | Describe each configurable input mode with its electrical requirements. Separate expansion capacity from populated ports. |
| PoLabs PoKeys57CNCEthernet/USB CNC and plasma I/O | Board layout, power, connector tables, motion and isolation, peripheral examples, electrical specifications, troubleshooting | Place minimum/maximum and signal type by connector function. State when several connectors share one supply budget. |
| Makerbase MKS DLC32 MAXLaser engraver and small CNC controller | Features, board diagram, dimensions, supply and laser interface specs, accessory inputs, configuration and firmware | Pair the board map with electrical notes for each connector. Put firmware-gated inputs in a support table. |
| MachBob2 MB2CNC breakout board for Ethernet SmoothStepper | Board specification, isolation, pin assignments, output circuits, power, setup, terminal diagrams and mounting | Show the host/accessory boundary and the domains of any isolated circuits. Publish a mechanical drawing with mounting information. |
| Board | Sections and information | Apply to Smoothieboard V2 |
|---|---|---|
| Arduino UNO R4 MinimaGeneral microcontroller board | Features, operating conditions, block diagram, board topology, power tree, pinout, accessories and declarations | Adopt a compact min/typ/max table with units and a separate board-level signal-flow diagram. |
| Arduino UNO R4 WiFiNetworked microcontroller board | Features, operating ratings, block diagram, board view, processor and radio, power tree, pinout and declarations | Show a labeled board view and call out the distinction between main and auxiliary processors. |
| Arduino GIGA R1 WiFiSTM32H7 development board | Operating conditions, block diagram, board topology, dual-core processor, communications, power tree, pin tables and declarations | Use clearly named silicon and firmware roles. Put the power tree beside the ratings that refer to its rails. |
| Arduino Nano EveryCompact microcontroller board | Features, operating conditions, power consumption, topology, connectors and pins, mechanical and compliance information | Keep power consumption and supply limits adjacent with measurement status and conditions. Use a numbered pin diagram and tables. |
| Raspberry Pi PicoEmbedded microcontroller board | Pinout, mechanical and operating specs, power use, ADC notes, ways to power, schematic and revision history | Illustrate alternate supply paths and explain shared returns and analog reference limits. |
| Raspberry Pi Pico WWireless microcontroller board | Pinout, mechanics, operating conditions, ADC limitations, powerchain, wireless integration, revision history | Add layout and integration constraints where an interface depends on the physical assembly. Document shared pins and their operating mode. |
| Raspberry Pi Pico 2Embedded microcontroller board | Pinout, mechanical specification, recommended conditions, measured consumption by workload, power, schematic and revisions | Give the bench configuration and workload for typical consumption. Keep an unpublished value open until it can be measured. |
| Raspberry Pi Compute Module 4Embedded computer module | Variant matrix, interfaces, mechanical data, absolute limits, operating conditions, pinout, carrier-board power and thermal information | Lead with a variant matrix. Keep stress limits distinct from recommended conditions and describe the load and ambient assumptions. |
| BeagleBone BlackEmbedded Linux board | Silicon and board features, block diagrams, power modes, consumption by state, connectors, expansion and mechanical drawings | Make a board power diagram and distinguish boot, idle and loaded consumption. Record which peripherals were powered during each reading. |
| Electro-Smith Daisy SeedEmbedded music and audio module | Pinout, absolute limits, pin functions, electrical characteristics, application circuits, document history | Publish one absolute-limits table with clear pin families. Show alternate functions and give worked interfaces in an appendix. |
Selected original pages illustrate the patterns in the table. Click a capture to enlarge it. Page numbers follow PDF order, including covers and front matter. Each full source PDF is linked at its publisher. Browse the full source catalog.
| Content | What the references show | Smoothieboard V2 treatment |
|---|---|---|
| Identity and variants | Compute Module 4 and the Arduino board sheets give the reader the product identity and main differences up front. | Identify the two Prime driver designs and the Core logic board. Include hardware revision, identifying marks, firmware target, and shared versus revision-specific interfaces. |
| Ratings and test conditions | The Mesa boards tabulate limits by signal and load. Raspberry Pi and Daisy distinguish operating conditions from stress limits. | Separate recommended min/typ/max, absolute limits, and typical measured performance. State temperature, cooling, rails, loads, channel count and current basis. Keep unverified cells visible. |
| Power and protection | The Pico and BeagleBone diagrams show where current comes from. MachBob2 identifies isolation domains. | Draw motor and switched-load rails, logic power selection, power returns, shared current limits, rail sense, and the output cutoff boundary. Add source-priority and startup/fault behavior when verified. |
| Motion, loads and sensing | Centroid and PoLabs explain what individual external circuits expect to see. | Specify motor phases, step/direction timing for external drives, heater/fan/bed and control outputs, input thresholds and polarity, ADC range and accuracy, probe jumper modes, and return pins. |
| Connectors and mechanical fit | Makerbase and AcornSix use board-facing views and dimensioned drawings. Arduino and Daisy number pins and list their alternate functions. | Provide a correctly oriented connector map and individually numbered tables. Mark shared nets, pin 1, mounting datum, screw hole pattern, component height, and required cable clearance. |
| Firmware and qualification | Pico 2 reports power with workload conditions. CNC manuals pair hardware with access, startup or compatibility notes. | Record minimum verified firmware, features and file names, confirmed host protocols, environmental and regulatory evidence, and published document revisions. Move setup walkthroughs and full schematics to linked references. |
Eight schematic page layouts show the reading order and what belongs together. The boxes represent information blocks. A short datasheet can combine adjacent panels if the electrical tables stay readable.
Let the reader match the physical board and choose the right column before looking up a rating.
Show where motor, switched loads, logic and accessory rails get power. Label dependency on the source and any shared cutoff.
Give phase-current basis, output load limits and simultaneous-load restrictions. Keep driver chip capabilities tied to the driver.
Give input modes, thresholds and required returns. Show which values depend on jumper state and board revision.
Use the board layout as the spatial index. Each connector table gives contact order, signal role, electrical notes and shared functions.
Distinguish physical ports, available firmware features and reserved or shared nets.
Use revision-qualified CAD for nominal geometry and assembly checks for clearances. Publish thermal limits with test conditions.
Link hardware and firmware revisions, qualification reports, declarations, and changes to ratings.
Full pages from the downloadable PDF. Select a page to enlarge it. The appendices begin on page 9. Browse the board renderings, wiki links, or configuration settings.
Download a labeled component-side drawing as a scalable SVG.
| Topic | Documentation |
|---|---|
| Start and upgrade | Getting started · Basics · How to wire · SD card setup · Download firmware · Flash firmware · Migrate from GRBL · Migrate from Marlin |
| Machine guides | CNC mill · Laser cutter · 3D printer · Pick and place · Lathe · Electronic leadscrew |
| Board and connections | Smoothieboard V2 Prime · V2 schematic · STM32H7 pin usage · Pin configuration · Differences from V1 |
| Configure motion | Configuration file · Configuration options · Motion control · Kinematics · Additional axes · Axis slaving · GRBL mode · Current control · Endstops · Probing |
| Configure tools | Laser module · Spindle module · Extruder · Temperature control · Switch inputs and outputs |
| Operate and troubleshoot | Communication · G-code reference · Console commands · Feed hold and cycle start · Emergency stop · Software · Network · USB · UART · Troubleshooting · Error messages |
Use the INI section and key shown on each row. alpha, minx, hotend, and fan are example instance names. Select the matching actuator, endstop, tool, or switch from the configuration for your board and firmware.
The Default column shows the firmware fallback for each omitted key in a configured section. Sample configurations may override these values. "" means an empty string and nc means no pin is assigned.
For the full references, see Configuration options, the configuration file guide, the V2 settings database, and the V2 firmware configuration examples.
| INI section | Key | Default | What it controls |
|---|---|---|---|
[general] | grbl_mode | false | Enable GRBL-compatible command and status behavior. |
[general] | config-override | false | Allow persistent runtime configuration overrides. |
[system] | step_frequency | 200,000 Hz (50,000 debug) | Set the step generation frequency in Hz. |
[system] | step_pulse_us | 1 µs | Set STEP pulse width in µs. |
[system] | msc_enable | true | Enable USB mass-storage access. |
[consoles] | second_usb_serial_enable | false | Enable the second USB serial console. |
[uart console] | enable | false | Enable the serial console on a hardware UART. |
[uart console] | baudrate | 115,200 baud | Set the serial console baud rate. |
[motion control] | arm_solution | cartesian | Select the machine kinematics. |
[motion control] | default_feed_rate | 4,000 mm/min | Default feed rate for cutting or printing moves. |
[motion control] | default_seek_rate | 4,000 mm/min | Default rapid move rate. |
[motion control] | default_acceleration | 100 mm/s² | Default acceleration for planned moves. |
[motion control] | x_axis_max_speed | 60,000 mm/min | Limit X travel speed. |
[motion control] | y_axis_max_speed | 60,000 mm/min | Limit Y travel speed. |
[motion control] | z_axis_max_speed | 300 mm/min | Limit Z travel speed. |
[motion control] | max_speed | 0 (disabled) | Limit coordinated move speed. |
[motion control] | must_be_homed | false (true on delta) | Require homing before motion. |
[motion control] | save_wcs | false | Persist work coordinate offsets. |
[motion control] | mm_per_line_segment | 0 mm | Control straight-move segmentation length. |
[motion control] | mm_per_arc_segment | 0 mm (automatic) | Set the arc segmentation length. |
[motion control] | mm_max_arc_error | 0.01 mm | Set maximum chord error for arc approximation. |
[planner] | junction_deviation | 0.05 mm | Adjust cornering speed through move junctions. |
[planner] | z_junction_deviation | -1 (inherit XY) | Adjust cornering for junctions involving Z. |
[planner] | minimum_planner_speed | 0 mm/s | Set the planner's minimum junction speed. |
[conveyor] | queue_delay_time_ms | 100 ms | Set the initial move-queue delay in ms. |
| INI section | Key | Default | What it controls |
|---|---|---|---|
[actuator] | alpha.steps_per_mm | 80 steps/mm | Set steps per unit of travel for the actuator. |
[actuator] | alpha.max_rate | 30,000 mm/min | Limit the actuator's motion rate. |
[actuator] | alpha.acceleration | -1 (inherit motion) | Set the actuator acceleration limit. |
[actuator] | alpha.step_pin | PD3 (Prime), nc (Core) | Assign the STEP pin for an external driver. |
[actuator] | alpha.dir_pin | PD4 (Prime), nc (Core) | Assign the direction pin for an external driver. |
[actuator] | alpha.en_pin | nc | Assign the enable pin for an external driver. |
[actuator] | alpha.driver | Prime driver by board ID¹ | Select the driver type. |
[actuator] | alpha.microsteps | 32 | Set microstep resolution for the onboard driver. |
[actuator] | alpha.reversed | false | Reverse the actuator direction. |
[actuator] | delta.slaved_to | "" | Set which primary actuator the secondary motor follows. |
[actuator] | common.check_driver_errors | true | Check onboard driver fault status. |
[actuator] | common.halt_on_driver_alarm | false | Halt on detected driver alarms. |
[current control] | alpha.current | Unset | Set the motor phase current for the channel. |
[endstops] | minx.enable | false | Enable the named endstop. |
[endstops] | minx.pin | nc | Assign the endstop input. |
[endstops] | minx.axis | "" (axis required) | Assign the endstop to an axis. |
[endstops] | minx.homing_direction | none | Select the direction of the homing move. |
[endstops] | minx.homing_position | 0 mm (min), 200 mm (max) | Set the machine coordinate at home. |
[endstops] | minx.max_travel | 500 mm | Set the maximum search distance during homing. |
[endstops] | minx.fast_rate | 100 mm/s | Set the initial homing approach speed. |
[endstops] | minx.slow_rate | 10 mm/s | Set the slow homing approach speed. |
[endstops] | minx.retract | 5 mm | Set the retract distance before the slow approach. |
[endstops] | minx.limit_enable | false | Use the endstop as a hard limit. |
[endstops] | common.debounce_ms | 0 ms | Set endstop debounce time in ms. |
[endstops] | common.homing_order | "" (simultaneous) | Set the axis homing sequence. |
¹ Prime selects tmc2660 for board ID 1 and tmc2590 otherwise in builds with onboard Trinamic support. Core uses external drivers.
| INI section | Key | Default | What it controls |
|---|---|---|---|
[zprobe] | enable | false | Enable the probe module. |
[zprobe] | probe_pin | nc | Assign the probe input. |
[zprobe] | slow_feedrate | 5 mm/s | Set the slow probing speed. |
[zprobe] | fast_feedrate | 100 mm/s | Set the rapid probing approach speed. |
[zprobe] | return_feedrate | 0 (automatic) | Set the speed used to retract after probing. |
[zprobe] | probe_height | 5 mm | Set the starting clearance for probing. |
[zprobe] | max_travel | 200 mm | Limit the probe search distance. |
[zprobe] | reverse_z | false | Reverse the Z probing direction. |
[zprobe] | debounce_ms | 0 ms | Set probe input debounce time in ms. |
[temperature control] | hotend.enable | false | Enable the named temperature controller. |
[temperature control] | hotend.sensor | thermistor | Select the sensor type. |
[temperature control] | hotend.thermistor_pin | ADC1_1 (Prime), "" (Core) | Assign the analog thermistor input. |
[temperature control] | hotend.thermistor | "" (no preset) | Select the thermistor model. |
[temperature control] | hotend.heater_pin | PE0 (Prime), nc (Core) | Assign the heater control output. |
[temperature control] | hotend.max_pwm | 255 | Limit heater PWM output. |
[temperature control] | hotend.p_factor | 10 | Set proportional PID gain. |
[temperature control] | hotend.i_factor | 0.3 | Set integral PID gain. |
[temperature control] | hotend.d_factor | 200 | Set derivative PID gain. |
[temperature control] | hotend.min_temp | 0 °C | Set the lower allowed temperature reading. |
[temperature control] | hotend.max_temp | 300 °C | Set the upper allowed temperature reading. |
[temperature control] | hotend.runaway_heating_timeout | 300 s | Set the heating runaway timeout. |
[extruder] | hotend.enable | false | Enable the named extruder. |
[extruder] | hotend.tool_id | 0 | Associate the extruder with a tool number. |
[extruder] | hotend.filament_diameter | 0 (disabled) | Set filament diameter for volumetric extrusion. |
[extruder] | hotend.retract_length | 3 mm | Set firmware retraction distance. |
| INI section | Key | Default | What it controls |
|---|---|---|---|
[laser] | enable | false | Enable the laser module. |
[laser] | pwm_pin | nc | Assign the laser power PWM signal. |
[laser] | ttl_pin | nc | Assign the separate laser on/off signal. |
[laser] | inverted_pwm | false | Invert the laser PWM signal. |
[laser] | maximum_power | 1 | Set the maximum normalized laser output. |
[laser] | minimum_power | 0 | Set the minimum normalized firing power. |
[laser] | maximum_s_value | 1 | Set the G-code S value corresponding to full scale. |
[laser] | default_power | 0.8 | Set the initial laser power request. |
[laser] | proportional_power | true | Scale requested power with actual move speed. |
[switch] | fan.enable | false | Enable the named switch instance. |
[switch] | fan.input_pin | "" | Assign the switch's input pin. |
[switch] | fan.output_pin | nc | Assign the switch's output pin. |
[switch] | fan.output_type | "" (type required) | Select the output behavior or PWM type. |
[switch] | fan.input_on_command | "" | Bind the command that turns the output on. |
[switch] | fan.input_off_command | "" | Bind the command that turns the output off. |
[switch] | fan.startup_state | false | Set the output state at firmware start. |
[switch] | fan.halt_set_to | false | Set the output state requested on halt. |
[network] | enable | false | Enable the network module. |
[network] | ip_address | auto (DHCP) | Set the network address or select DHCP. |
[network] | ip_mask | 255.255.255.0 | Set the static IPv4 subnet mask. |
[network] | ip_gateway | 192.168.1.1 | Set the static IPv4 gateway. |
[network] | hostname | smoothiev2 | Set the network hostname. |
[network] | shell_enable | false | Enable the network command shell. |
[network] | webserver_enable | false | Enable the HTTP server. |
[network] | ftp_enable | false | Enable the FTP server. |